Electrical: Page 20

Victron energy UTP Patch Lead 0.3m.

Victron energy UTP Patch Lead 1.8m.

Victron energy UTP Patch Lead 10m.

Victron energy UTP Patch Lead 20m.

Victron energy UTP Patch Lead 5m.

CE certified shore power cable with moulded 3 pin plug and connector. Features a power indication LED and protective cap on female connector for additional safety.

Heavy duty shunt for measuring current up to 1000 Amps. This shunt can be used with any of the Victron BMV meters to increase the current range to 1000 Amps.

The Skylla Control allows you to alter the charge current and see the system status.

A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air.  The right amount of charge for a lead-acid battery: variable absorption time BatterySafe mode: preventing damage due to excessive gassing Storage mode: less maintenance and aging when the battery is not in use Smaller and lighter compared to similar models NMEA2000 Canbus connection PowerControl: set a maximum shore power Remote Control Li-ion (LiFePo4) ready

Features include: Temperature sensor, use as a power supply, forced cooling. Remotely control and monitor the extensive features of your SmartSolar MPPT charger with built-in bluetooth by pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN(long-range wide area network) device, available optionally. The intelligent Load output function prevents damage caused by running batteries 'flat'. You can configure the voltage at which SmartSolar disconnects a load - thereby preventing excessive drain on your batteries. And here's the clever bit: SmartSolar will attempt a 100% recharge every day. If it can't - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. Charge voltage 'absorption' / 'float': 28.5 V DC / 26.5 V DC. Charge current: 30 A. Charge characteristic: IUoUo (three step). Protection: output short circuit, battery reverse polarity detection, battery voltage too high, temperature too high. Operating temp. range -20 to 60°C (0 - 140°F). Humidity (non condensing) max 95%. Protection category IP 21.

Features include: Temperature sensor, use as a power supply, forced cooling. Input voltage / input voltage range: 230 V AC / 90 - 265 V AC. Frequency: 45-65 Hz / Power factor: 1. Charge voltage 'absorption' / 'float': 28.5 V DC / 26.5 V DC. Battery capacity: 250-500 Ah. Protection: IP21 / Output short circuit, battery reverse polarity detection, battery voltage too high, temperature too high. Charge current starter batt. / house batt.: 4 A / 50 A. Charge characteristic: IUoUo (three step). Remote alarm: Potential free contacts 60V / 1A (1x NO and 1x NC). Operating temp. range / Humidity (non condensing): -20 to 60°C / max 95%.

The Smart BMS CL 12/100 is a Battery Management system for Victron lithium-iron-phosphate (LiFePO4) Smart Batteries. It has been specifically designed for 12V systems with a 12V alternator. The BMS CL 12/100 monitors and protects each individual battery cell within the battery (or battery bank) and will disconnect the alternator, charge sources or DC loads in case of low battery voltage, high battery voltage or over temperature.

The SmartShunt is an all in one battery monitor, only without a display. A compatible smart phone acts as the display. The SmartShunt connects via Bluetooth to the VictronConnect App on the phone (or tablet) and can conveniently read out all monitored battery parameters, like state of charge, time to go, historical information and much more.

Replacement PCB for 500 Amp shunt on BMV 702 / 712 Battery Monitors.

UK 230V mains power cord for Smart IP43 & Skylla-S units. Length: 2m

Use this cable to connect a Victron product with a VE.Can port to a NMEA2000 network.

ASS030530209: Victron Ve Direct Cable 0.9M The VE.Direct cable used for comunication between Victron VE.Direct devices, it can also used to connect a Victron battery monitor to the Victron Colour Control.

ASS030530310: Victron Ve Direct Cable 10M The VE.Direct cable used for comunication between Victron VE.Direct devices, it can also used to connect a Victron battery monitor to the Victron Colour Control.

ASS030530250: Victron Ve Direct Cable 5M The VE.Direct cable used for comunication between Victron VE.Direct devices, it can also used to connect a Victron battery monitor to the Victron Colour Control.

The Venus GX is the communication-centre of your installation. Venus allows you to talk to all components in your system and ensure they are working in harmony. Monitoring of live data, and changing settings is performed by using your smartphone (or other device) via our free-to-use Victron Remote Management Portal (VRM).

Wall mount enclosure for Color Control GX.

Self-adhesive transparent function labels for 99726, 99728-30 - 25pcs Set

Our Marine batteries are specifically designed for boats engine start and auxillary use and to be continually ' cycled ', meaning that energy is taken out (discharged) and then energy put back in to the battery (recharged), via a battery charger or the Engines Alternator. A semi traction deep cycle marine battery incorporates thicker grids (plates) for extended life, designed for boats the...

YBX Active Marine batteries are ideal for yachts, motor boats, sailing boats and other water craft. Specifically designed to handle the rigours of wave pounding and trailer transport, they deliver reliable starting and auxiliary power and auxiliary power for on board systems. They incorporate advanced design features and specialist hard-wearing components for all marine applications.+   Features Specially developed to meet the demands of both starting and auxiliary power requirements Next generation EFB technology provides greater endurance, more available cycles & faster charging Vibrolock construction provides enhanced vibration resistance Dual terminal Supplied charged and ready to fit Enhanced safety features including integrated flame arrestor & carry handle Fully maintenance free Leak proof double lid 960 watt hours