Blue Sea Systems 4 Position, Below Deck Circuit Breaker Panel
Molded panel frame will stand up to UV and salt air making it perfect for power and sail boat electrical distribution.EASYLow profile makes it easy to install in tight spacesSIMPLE Fast-on circuit breaker connectors make it quick to wireCONVENIENTRed “ON” indicating LEDs for safe operation in low light condit
4 Carling Technologies™ 15A circuit breakers
Illuminated ON indication
Polycarbonate/ABS...
Blue Sea Systems 6 Position, Below Deck Circuit Breaker Panel
Molded panel frame will stand up to UV and salt air making it perfect for power and sail boat electrical distribution.
EASYLow profile makes it easy to install in tight spacesSIMPLE Fast-on circuit breaker connectors make it quick to wireCONVENIENTRed “ON” indicating LEDs for safe operation in low light conditions
6 Carling Technologies™ 15A circuit breakers
Illuminated ON indication
...
Blue Sea CLB Circuit Breaker Block - 6 Gang
Compact surface mount solution providing secure screw termination where Push Button Reset-Only CLB Circuit Breakers are desired.
Quick connect clips allow circuit breakers to snap easily into place
Tin-plated copper busses and screw terminals
Clear insulating cover with square format label recesses, satisfies ABYC/USCG insulation requirements
Easy to open clip on cover
Breakouts allow wire access...
Blue Sea CLB Circuit Breaker Block - 12 Gang
Compact surface mount solution providing secure screw termination where Push Button Reset-Only CLB Circuit Breakers are desired.
Quick connect clips allow circuit breakers to snap easily into place
Tin-plated copper busses and screw terminals
Clear insulating cover with square format label recesses, satisfies ABYC/USCG insulation requirements
Easy to open clip on cover
Breakouts allow wire access...
Blue Sea CLB Push Button Circuit Breaker
Blue Sea CLB push button circuit breaker compatible with Blue Sea circuit breaker block, breaker sizes 5A - 40A
Branch circuit breakers (also used for 24-hour circuit protection)
Compact design enables high density circuit protection configurations
Push-to-reset operation
Trip Free design cannot be held ON during fault current condition
Specification:
Interrupting Capacity: 3,000A...
Digital Battery Test Switch Panel
LED Display. Measurable Voltage – 3v to 30v
Connects to two battery banks with selector switch for the display.
IP65
75.2mm wide
62.5mm high
53.5mm deep…
6 Gang 12v Aluminium Vertical Breaker Panel
6 Gang Vertical Circuit Breaker Panel
Stamped anodised black aluminum panel with 6 illuminated switches, circuit breakers and spare labels.
Panel rating: 12 volts
Individual Circuits: 1x10 amp, 1x8amp, 2x6amp, 2x3amp
Press to reset
Dimension A: 165mm
Dimension B: 115mm
Dimension C: 140mm
Dimension D: 89mm
Sea-Dog Aluminum Horizontal 6 Switch Panel
6 Switch Horizontal Panel
Stamped anodized aluminum panel with 6 illuminated switches and spare labels
Panel rating: 12 volts, 37 amps total.
Individual circuit 10 amps
Dimension A: 115mmDimension B: 165mmDimension C: 89mmDimension D: 140mm
Vetus Rocker Switch For Windscreen Wipers
Three-position switch (off,1,2) suitable for a single two-speed wiper motor.
Use with Vetus wiper motors RWS, DIN and HDMC but not suitable for model ORW.
Max. switching current: 20A
Max. panel thickness: 6mm
Vetus Rotary Windscreen Wiper Switch
Three-position switch (off,1,2) for one wiper motor. Type HDMSW, for two-speed wiper motors.
Suitable for wiper motors RWS, DIN and HDMC.
Not suitable for model ORW.
Max. switching current:
20A Max.
Panel thickness:7 mm
Push Button Horn Switch
Push Button Horn/Starter switch for flush fitting.
Waterproof Push Button Horn Switch with screw-in terminals.
12v DC 5amp
Hole size around 18/19mm
Button size around 25mm
Waterproof Toggle switch
Toggle Switch
On/Off panel mount toggle switch with waterproof cover.
Mounting aperture 12mm
12v 15a
Spade Terminal Connections
Toggle Switch 2 Position (on-off)
Thermo Plastic Toggle Switch 12v DC - Without Illumination
2 Position (on-off) dash mount toggle switch
15A 12v - 10A 24v
Toggle Switch 3 position
3 Position dash mount Toggle Switch On/Off/On
Max panel thickness 5mm
Mounting Aperture 12mm
Carling V Series Contura II Actuator - Running Lights
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Running Lights
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Light
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Light
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Horn
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Horn
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Fan
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Fan
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Windscreen Wiper
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Windscreen Wiper
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Anchor Light
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Anchor Light
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Bilge Pump
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Bilge Pump
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Search Light
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Search Light
Actuator only, switch sold separately
Carling V Series Contura II Actuator - Plain with Lens Bar
Carling Switch Actuator to fit Carling V Series Contura II Switches
Legend: Plain with Lense Bar
Actuator only, switch sold separately
Carling V Series End Mounting Panel
End mounting panel for Carling V Series switches enables easy dash mounting.
Modular sections
Multiple mounting panels to create custom switch panel
Carling V Series Center Mounting Panel
Center mounting panel for Carling V Series switches enables easy dash mounting.
Modular sections
Multiple mounting panels to create custom switch panel
Carling V Series Single Mounting Panel
End mounting panel for Carling V Series switches enables easy dash mounting.
Modular sections
Multiple mounting panels to create custom switch panel
Carling V Series Contura II Switch On/Off
Carling V Series Contura II On/Off Switch Only.
Red LED Back Light
Switch Function: Standard On - Off
Specification:
Contact Rating: 20 amps 4 - 14V DC
15 amps 15-28V DC
Life: 50,000 - 100,000 cycles circuit dependent
Terminals: 6.3mm quick connect blade terminals
Order Actuator and switch housing separately
Carling V Series Contura II Switch Off/(On)
Carling V Series Contura II Off/(On) Switch Only.
Red LED Back Light
Switch Function: Off - (Momentary On)
Specification:
Contact Rating: 20 amps 4 - 14V DC
15 amps 15-28V DC
Life: 50,000 - 100,000 cycles circuit dependent
Terminals: 6.3mm quick connect blade terminals
Order Actuator and switch housing separately
Carling V Series Contura II Switch (On)/Off/(On)
Carling V Series Contura II (On)/Off/(On) Switch Only.
Red LED Back Light
Switch Function: (Momentary On) - Off - (Momentary On)
Specification:
Contact Rating: 20 amps 4 - 14V DC
15 amps 15-28V DC
Life: 50,000 - 100,000 cycles circuit dependent
Terminals: 6.3mm quick connect blade terminals
Order Actuator and switch housing separately
Carling V Series Contura II Switch On/Off/On
Carling V Series Contura II On/Off/On Switch Only.
Red LED Back Light
Switch Function: On - Off - On
3 position suitable for 2 speed wiper motor
Specification:
Contact Rating: 20 amps 4 - 14V DC
15 amps 15-28V DC
Life: 50,000 - 100,000 cycles circuit dependent
Terminals: 6.3mm quick connect blade terminals
Order Actuator and switch housing separately
Sterling Split Charge Diode
Sterling Split Charge Diode
A versatile battery management system which allows simultaneous charging through a diode system which ensures power is evenly distributed through the boats battery banks. Most boats have at least 2 battery banks, some have 3 and these tend to be the engine start battery, the domestic battery bank (please note that if you join three or four batteries together in your domestic...
Battery Isolator Switch
Battery Isolation Switch
Intended for isolating a single battery.
Can also be used for controling high current devices such as winches, windlasses, capstans etc.
Maximum Voltage: 24 Vdc
Maximum Surge Current: 500Amps for 10 seconds @ 12Vdc
Maximum continuous current: 100Amps/140Amps @ 12Vdc
Dimensions: 75mm x 60mm diameter
Terminal Stud Diameter: 10mm
Battery Isolator Switch c/w Protective Cap
Battery Isolation Switch with Protective Cap
Intended for isolating a single battery.
Can also be used for controling high current devices such as winches, windlasses, capstans etc.
Maximum Voltage: 24 Vdc
Maximum Surge Current: 500Amps for 10 seconds @ 12Vdc
Maximum continuous current: 100Amps/140Amps @ 12Vdc
Dimensions: 75mm x 60mm diameter
Terminal Stud Diameter: 10mm
Battery Isolator Switch c/w Protective Cap 135 amp
Basic battery isolation switch
Intended for isolating a single battery.
Can also be used for controling high current devices such as winches, windlasses, capstans etc.
Maximum Voltage: 12- 24 Vdc
Maximum Surge Current: 400Amps 25mm sq cable
Maximum continuous current: 100Amps/135Amps @ 12Vdc
Terminal Stud Diameter: 10mm
Spare Red Key for Battery Isolator Switch
Spare Red Key for Battery Isolator Switch
Universal handy spare key for battery isolator switch
BEP Battery Management System
Heavy duty dual battery charging made easy, an ideal replacement for a Battery Selector Switch.
Simply remove existing selector switch and connect existing wires to a 716 cluster no extra wires are required for a fully automatic battery management system.
Fully automatic - No more flat start batteries.
Electronics protection from harmful engine start spikes.
Easy replacment for existing...
Vetus Heavy Duty Battery Changeover Switch 175 amp Continuous
Vetus Heavy Duty Battery Changeover Switch
The famous VETUS battery selector switch is a sturdy rotary series switch. It enables battery usage and charging.
From the OFF position, in accordance with the switch pattern, battery 1 only, battery 1 plus battery 2 or battery 2 only can be switched on.
The switch enables usage and charging of the batteries individually and in parallel connection.
The...
Blue Sea Systems Mini Battery Selector Switch
BLUE SEA M-SERIES 4 POSITION BATTERY SWITCH
300 Ampere continuous rating for outboards and small gasoline or diesel engines.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 3⁄8" (M10) ring terminals
One-piece terminal stud design never loosens over time
7⁄8" (22.22mm) stud length accepts multiple cable terminals
Isolating cover with three snap-in side...
Blue Sea Systems Mini Battery Switch (Knob Version)
Blue Sea M-Series Battery Switches
300 Ampere continuous rating for outboards and small gasoline or diesel engines.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 3⁄8" (M10) ring terminals
One-piece terminal stud design never loosens over time
7⁄8" (22.22mm) stud length accepts multiple cable terminals
Isolating cover with three snap-in side pieces...
Blue Sea Systems Mini Battery Switch (Key Version)
Blue Sea M-SERIES BATTERY SWITCHES
300 Ampere continuous rating for outboards and small gasoline or diesel engines.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 3⁄8" (M10) ring terminals
One-piece terminal stud design never loosens over time
7⁄8" (22.22mm) stud length accepts multiple cable terminals
Isolating cover with three snap-in side pieces...
Blue Sea Systems E-Series Selector Battery Switch
Blue Sea E-Series 4 Position Battery Switch
Select either battery bank or both plus an off position, 350 Ampere continuous rating for inboard petrol and diesel engines.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 3⁄8" (M10) ring terminals
7⁄8" (22mm) stud length accepts multiple cable terminals
One-piece terminal stud design never loosens over...
Blue Sea Systems Dual Circuit Plus Battery Switch 5511E
Blue Sea E-Series Dual Circuit Battery Switch
A high quality battery switch for craft with a dual battery installation. This switch has the ability to switch two isolated batteries to two isolated loads i.e. Starting battery to starter motor and house battery to domestic circuits. When the switch is set to the Combine position, both batteries are connected in parallel to the loads. Make before break...
Blue Sea Systems E-Series Single Circuit ON/OFF Battery Switch
Blue Sea E-SERIES BATTERY SWITCHES
350 Ampere continuous rating for inboard petrol and diesel engines.
Tin-plated copper studs for maximum conductivity and corrosion resistance
Studs accept 3⁄8" (M10) ring terminals
7⁄8" (22mm) stud length accepts multiple cable terminals
One-piece terminal stud design never loosens over time
Case design allows surface or rear panel mounting options
Label...
Blue Sea H/Duty Battery Switch 4 Way 500A
HD BATTERY SWITCHES (Heavy Duty) Up to 600 Ampere continuous rating for large diesel engines.Label with international legendsTactile indicator conveys knob position by feelAccepts up to 4/0 AWG (120mm2) battery cablesCase design allows surface or rear panel mounting7/8" (22mm) stud length accepts multiple cable terminalsOne-piece terminal stud design never loosens over timeM12 tin-plated copper studs...
Battery Box Standard Red 270x195x200mm
Plastic Battery Box
Supplied with securing strap and essential to avoid spillages in to the boat.
Size: L270 x W195 x H200 mm
Large Battery Box 410x200x250mm
Large battery box designed with adjustable partition to suit different battery case sizes.
Suppled with fitting strap, this is ensential to prevent spillages leaking in to the boat.
Size: L410 x W200 x H250mm
Blue Sea Systems 150A Common BusBar with Cover - 10 Gang
Blue Sea 10 Gang Busbar
The industry standard busbar for positive distribution
The industry standard busbar for the collection of negative or AC ground circuits.
Rating:
130 Amps AC / 150 Amps DC
Max Voltage Rating: 300V AC / 48V DC
Bus Material: Tin-Plated Copper
Base Material: Reinforced Polycarbonate
Blue Sea Systems 150A Common BusBar with Cover - 20 Gang
Blue Sea 20 Gang Busbar
The industry standard busbar for the collection of negative or AC ground circuits
Cont. Rating:
130 Amps AC / 150 Amps DC
Max Voltage Rating: 300V AC / 48V DC
Bus Material: Tin-Plated Copper
Base Material: Reinforced Polycarbonate