Engine Cooling Water Inlet Strainer
Engine Water Inlet Strainer with mounting bracket
Engine inlet water strainer with plastic body and a stainless steel filter.
The clear removable cover allows easy access to clean the filter gauze.
This smaller engine water strainer has a built in side mount bracket, and can be used for 3/4', 1' and 1-1/4' hoses.
Max flow rate is 150 litres per minute.
Heat Resistant Rubber Heater Hose
Synthetically reinforced EPDM rubber Temperature Range: -45ºC to +120ºC suitable for engine coolant and hot water applications.
Priced per mtr
Water Lubricated Shaft Cutlass Bearing 1-1/4 x 2 x 5 "
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Grease Cup 1/8' BSP x 25mm
Grease Cup “Stauffors” type grease cups in hot stamped brass suitable for stern tube lubrication or other onboard applications.
For best performance, once installed pack tightly with white marine grease.
Grease Cup Sizing:
BSP Male Thread Size x O/A Dia. x Max Height
1/8"BSP x 25mm x 30mm
Heavy Duty Engine Inlet Water Strainer
Engine inlet water strainer with plastic body and stainless steel filter.
This larger model has a max flow rate 300 litres per minute and has two 1-1/2' BSP female ports.
Varying sizes of hose tail can be used on this water strainer and these can be found in the water section of this website.
Dimensions: H180mm x Dia.190mm
Supplied with aluminium mounting bracket
Bulkhead Mounted Engine Water Strainer - 1"BSP
Bulkhead mounted engine water strainer with clear polycarbonate lid.
Size: H145mm x W151mm
Thread: 1" BSP Parallel
Nickel plated Bronze body
Vertical inlet & horizontal outlet
AISI 316L S/S filter basket
Transparent polycarbonate top
Approved by R.I.N.A.
Flow Rate: @ 0.1Bar 7950
Flow Rate: @ 1bar 25500
Bulkhead Mounted Engine Water Strainer - 1-1/4"BSP
Bulkhead mounted engine water strainer with clear polycarbonate lid.
Size: H168mm x W167mm
Thread: 1-1/4" BSP Parallel
Nickel plated Bronze body
Vertical inlet & horizontal outlet
AISI 316L S/S filter basket
Transparent polycarbonate top
Approved by R.I.N.A.
Flow Rate: @ 0.1Bar 12100
Flow Rate: @ 1bar 38200
Bulkhead Mounted Engine Water Strainer - 1-1/2"BSP
Bulkhead mounted engine water strainer with clear polycarbonate lid.
Size: H178mm x W180mm
Thread: 1-1/2" BSP Parallel
Nickel plated Bronze body
Vertical inlet & horizontal outlet
AISI 316L S/S filter basket
Transparent polycarbonate top
Approved by R.I.N.A.
Flow Rate: @ 0.1Bar 19100
Flow Rate: @ 1bar 61250
Bulkhead Mounted Engine Water Strainer - 2"BSP
Bulkhead mounted engine water strainer with clear polycarbonate lid.
Size: H215mm x W213mm
Thread: 2" BSP Parallel
Nickel plated Bronze body
Vertical inlet & horizontal outlet
AISI 316L S/S filter basket
Transparent polycarbonate top
Approved by R.I.N.A.
Flow Rate: @ 0.1Bar 30000
Flow Rate: @ 1bar 96200
Bulkhead Water Strainer Brackets
L - shaped mounting brackets for fitting of bulkhead strainers.
304 stainless steel
Drilled with fasteners for connection to strainer
Larger strainers require double L Bracket Kit
Water Lubricated Cutlass Shaft Bearing 1.625" x 2.25" x 6.5" **One Only **
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft and at the same time assist the flow of water into the bearing, providing lubrication exactly where it is needed.
The profile of the grooves is specially...
Water Lubricated Shaft Cutlass Bearing 1-3/4 x 2.5/8 x 7
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 3/4 x 1-1/4 x 3
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 1 x 1-3/8 x 4
Cutlass Bearing
shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 1 x 1-1/2 x 4
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 1-1/4 x 1-3/4 x 5
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 1-1/2 x 2 x 6
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 25mm x 40mm x 100mm
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and high loads.
The bearings support the shaft...
Water Lubricated Shaft Cutlass Bearing 30mm x 45mm x 120mm
Cutlass Bearing
Shaft or cutlass bearings are manufactured using a specially compounded synthetic rubber lining which is moulded into a strong outer shell.
The lining of the bearing has shaped grooves, or flutes, designed specifically to optimise water lubrication, giving very low friction and helping to maintain hydrodynamic lubrication even at low speeds and hig h loads.
The bearings support the...
A1 Marine Grade Fuel Hose
A1 Marine Grade Fuel Hose
Suitable for all marine engine fuel line systems with a temp range -35ºC to +100ºC, also oil resistant suitable for most applications including vent breather.
Fuel (petrol/diesel) resistant
Manufactured to EN ISO7840
Heat, oil, abrasion resistant
Internal diameter: 6mm, 8mm, 10mm, 12.5mm, 16mm, 19mm
Price per mtr
A2 Marine Grade Fuel Hose
A2 Grade Marine Fuel Hose
Suitable for all marine engine fuel systems with a temp range -35ºC to +100ºC, also oil resistant suitable for most applications including vent breather.
Fuel (petrol/diesel) resistant
Manufactured to EN ISO7840
Heat, oil, abrasion resistant
Wire reinforced suitable for deck filling
Internal diameter: 38mm, 50mm
Price per mtr
JCS Rubber Lined P Clips
JCS rubber-lined P-Clips are tough and durable, providing a simple and secure fixing solution for even the most challenging of environments.
The standard P Clip is supplied with TPE rubber liner which prevents chafing or damage to the surface of the item being clamped.
Snug fitting TPE rubber liner absorbs vibration and prevents chafing of pipe or cable, and water penetration into the clamping...
Heavy Duty Stainless Steel Hose Clamp 48-51mm (40mm hose)
Heavy duty stainless steel hose clamps for use with marine exhaust hose.
Using a socket or a screw driver, these clamps will tighten down on the wire reinforced hose giving a secure fixing.
Suitable for 40mm wire reinforced marine exhaust hose
Hose Clamp 48-51mm
Heavy Duty Stainless Steel Hose Clamp 52-55mm (45mm hose)
Heavy duty stainless steel hose clamps for use with marine exhaust hose.
Using a socket or a screw driver, these are the only suitable clamps for exhaust hose as the clamps will tighten down on the wire reinforced hose giving a secure fixing.
Suitable for 45mm wire reinforced marine exhaust hose
Hose Clamp 52-55mm
Heavy Duty Stainless Steel Hose Clamp 60-63mm (50mm hose)
Heavy duty stainless steel hose clamps for use with marine exhaust hose.
Using a socket or a screw driver, these clamps will tighten down on the wire reinforced hose giving a secure fixing.
Suitable for 50mm wire reinforced marine exhaust hose
Hose Clamp 60-63mm
Heavy Duty Stainless Steel Hose Clamp 68-73mm (63mm hose)
Heavy duty stainless steel hose clamps for use with marine exhaust hose.
Using a socket or a screw driver, these clamps will tighten down on the wire reinforced hose giving a secure fixing.
Suitable for 63mm wire reinforced marine exhaust hose
Hose Clamp 68-73mm
Heavy Duty Stainless Steel Hose Clamp 86-91mm (75mm hose)
Heavy duty stainless steel hose clamps for use with marine exhaust hose.
Using a socket or a screw driver, these clamps will tighten down on the wire reinforced hose giving a secure fixing.
Suitable for 75mm wire reinforced marine exhaust hose
Hose Clamp 86-91mm
Marine Rubber Exhaust Hose 40mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Marine Rubber Exhaust Hose 45mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Marine Rubber Exhaust Hose 51mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Marine Rubber Exhaust Hose 63mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Marine Rubber Exhaust Hose 76mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Marine Rubber Exhaust Hose 90mm - Lloyds Approved
Lloyds Approved Marine Exhaust Hose manufactured with salt water resistant EPDM rubber and double steel helix wire reinforcing.
This strong rubber hose provides more flexibilty than other similar hoses allowing easier installation throughout the boat, ideally suited for marine applications.
It is essential to use heavy duty stainless steel hose clamps when fitting this type of hose as regular...
Grease Cup 1/4 BSP 40mm OD
Grease Cup
“Stauffors” type grease cups in hot stamped brass suitable for stern tube lubrication or other onboard applications.
For best performance, once installed pack tightly with white marine grease.
Grease Cup Sizing:
BSP Male Thread Size x O/A Dia. x Max Height
1/4' x 40mm x 42mm
Grease Cup 1/8' BSP x 33mm
Grease Cup
“Stauffors” type grease cups in hot stamped brass suitable for stern tube lubrication or other onboard applications.
For best performance, once installed pack tightly with white marine grease.
Grease Cup Sizing:
BSP Male Thread Size x O/A Dia. x Max Height
1/8' x 33mm x 40mm
James Walker 1/4" - 6.5mm Graphite Stern Gland Packing
James Walker RA0001321 Rapido Square 1/4" (6.5 mm)
Stern Gland Packing Graphite
Made from quality yarn lubricated & graphited prior to plaiting. Suitable forstern glands, pumps etc.
Sold by the Metre
Stern Gland Packing 5mm - 3/16 PTFE
Stern Gland Packing
3/16" - 5mm PTFE gland packing.
Approx length depending on size:450-550mm
Stern Gland Packing 6.5mm - 1/4 PTFE
Stern Gland Packing
1/4" - 6.5mm PTFE gland packing.
Approx length depending on size: 450-550mm
Stern Gland Packing 8mm - 5/16 PTFE
Stern Gland Packing
5/16" - 8mm PTFE gland packing.
Approx length depending on size:450-550mm
Stern Gland Packing 9.5mm - 3/8 PTFE
Stern Gland Packing
3/8" - 9.5mm PTFE gland packing.
Approx length depending on size:450-550mm
Stern Tube Quick Release Brass Greaser Kit
Greaser Kit
Guidi solid brass lubricator for stern tubes, rudder bearings and other onboard applications.
Mnaufactured in Italy this is a robust brass greaser designed for engine rooms and can be bulkhead or floor mounted and its simple and clean operation means that by winding down the screw, grease is automatically dispensed in to the shaft bearing.
Capacity: 150ml
Dimensions:
Base width 80mm x...
Marine Engine Exhaust Waterlock Silencer
Waterlock silencer manufactured of high quality plastic suitable for marine use and boat engines, this model of exhaust waterlock silencer is suitable for 40, 45 & 50mm diameter exhaust hose.
Installed within the exhaust system it will dramatically reduce noise
40mm/45mm/50mm Hose Connection
Size: 640L x 225W x 230H
Exhaust Gooseneck
Exhaust Gooseneck
Anti syphon gooseneck which prevents water entering the engine via the transom.
Supplied with stepped hose connection to suit 40mm, 45mm or 50mm exhaust hose and plastic fixing straps.
Hose Size: 40 - 45 - 50mm
Body Size: Width 110mm x Height 480mm
Weight: 0.70kg
Vetus Type NLP Waterlock
The NLP Waterlock compliments the well known and proven range of LP waterlocks, VETUS has now introduced several new models, type NLP, made of injection-moulded plastic materials.
These have the benefits of being durable, corrosion proof and light in weight, the new NLP waterlocks are of dual stage construction, featuring upper and lower chambers with a horizontal partition plate and a riser tube...
Vetus Exhaust Gooseneck
Vetus Exhaust Gooseneck
Gooseneck for exhaust hose with 40 - 45 - 51 mm internal diameter.
Raises the exhaust hose above the waterline so that water cannot backfill the exhaust system.
Vetus Anti-Syphon Vent
Vetus Anti-Syphon Air vent suitable for hoses of Ø 1/2', 3/4', 1' and 1-1/4' ,13, 19, 25 and 32 mm I.D.
If the point of injection of the cooling water is situated at a height less than 6' above the water line, then when the engine is stopped there is a risk that, as a result of syphoning, the cooling water may enter the engine.
Such syphoning may be avoided by positioning a VETUS air vent into...
Vetus Type K50 Max Load 50kg Engine Mount
Engine Mount
Vetus TYPE K engine mounts are for smaller engines, up to approx. 60 kW (8O HP).
The torque of an engine is one of the deciding factors for determination of the load applied to the Vetus engine mounts.
When more powerful engines are installed, it is important to use the following formula to define the load per support in kg (4 supporting points).
Engine weight in kg + kW x 487 x reduction...
Vetus Type K75 Max Load 75kg Engine Mount
Engine Mount
Vetus TYPE K engine mounts are for smaller engines, up to approx. 60 kW (8O HP).
The torque of an engine is one of the deciding factors for determination of the load applied to the Vetus engine mounts.
When more powerful engines are installed, it is important to use the following formula to define the load per support in kg (4 supporting points).
Engine weight in kg + kW x 487 x reduction...