Garmin Transducers

Keep your black box sonar on the water with this replacement right angle transducer adapter cable, which has 12-pins and is 0.6 m (23.6 in) long.

Garmin 30ft Xdcr Extension Cable 12 Pin With XID.

Connect a port/starboard pair of thru hull or transom mount transducers to the sonar unit with this 12-pin Y-cable. This cable allows the use of two different transducers to produce the left and right SideVü images to avoid engine lower unit or keel/hull shadowing.

Garmin 3m Transducer extension cable.

Connect a 4-pin transducer to an 8-pin sonar port on your compatible marine device with this adapter cable.

This transducer adapter allows you to use your existing 6-pin dual-beam transducer with your 4-pin echo™ series fishfinder. .

Freshwater Transducer for use w/echo Fishfinder Series.

10' (3M) 8 Pin heavy duty extension cable for the GT12M-THF or GT15M-THF Transducers.

Garmin 10ft Xdcr Extension Cable 8 Pin.

Use this adapter cable to connect an 8-pin transducer with XID to a 12-pin sonar port on a compatible marine device.

Garmin 6Pin Female to 8Pin Male Adapter.

This entry level CHIRP solution provides good depth capability and target separation.

This entry level CHIRP solution provides good depth capability and target separation. This 8-pin 300 W bronze thru-hull mount transducer has a depth of 1,500 ft; an operating frequency of 95-155 kHz; a beamwidth of 26/17 degrees; and a 16 to 24 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat.

Step up to 1 kW without a fairing with this flush-mounted bronze housing that protrudes less than 1/4-inch outside the hull and can sit on the trailer rollers/bunks without damage. The tilted element inside the transducer accommodates all hull deadrises and eliminates the need for a fairing block. And, low, medium and high frequency versions provide maximum flexibility for the choice of frequencies. An excellent choice for fiberglass and wood hulls, this 8-pin transducer has a depth of 1,200 ft; an operating frequency of 130-210 kHz; a beamwidth of 9-15 degrees; and a 16 to 24 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat.

This mid-range 1 kW 8-pin transducer with a narrow beam is good for deep water and bottom definition. It has a depth of 1,500 to 2,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 14x23 to 3x5 degrees; and a 0 to 26 degree deadrise.

This bronze thru-hull mount transducer performs well at high speeds and is an excellent choice for fiberglass and wood hulls. This 8-pin 500 W transducer has a depth of 900 ft; an operating frequency of 77/200 kHz; a beamwidth of 45/15 degrees; and a 16 to 24 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. *Do not use on metal hulls.

Garmin 010-11634-22 Airmar B75H Bronze Thru-Hull Transducer with Garmin 8 Pin Connector 20° Tilted version for 16°-24° deadrise Our bronze thru-hull mount transducer is designed to allow both traditional and spread spectrum scanning when used with a compatible sonar. A 600 W transducer with 8 pins, it has a depth of 800 ft; an operating frequency of 130-210 kHz; a beamwidth of 15/9 degrees; and a 16 to 24 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat

Garmin 010-11105-00 Airmar DT800 Smart Sensor 20 Degree 20° Tilted version for 16° - 24° hull deadrise The DT800 utilizes Airmar’s proven Tilted Element and broadband technologies in this thru-hull depth and temperature Smart Sensor. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA2000 display or network. Airmar's Smart Sensors have embedded microelectronics - the transducer element and signal processor are only millimeters apart. The signal from the depth transducer is processed right inside the sensor itself. All that is needed to receive depth and temperature data is a single cable into a compatible network or display.

This plastic thru-hull mount transducer performs well at high speeds and is an excellent choice for fiberglass and metal hulls.

When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required.

The P66 combines Depth, Speed and Temperature into a single Multisensor transom-mount transducer. Featuring a 50/200 kHz, dual-frequency, single, ceramic element. This hydrodynamic housing with its rounded nose reduces the turbulence under the transducer’s acoustic face for accurate high-speed readings and clear display images.

This plastic in-hull transducer with an adjustable deadrise angle makes installation a snap. The NMEA 2000 100 W transducer has a depth of 500 ft; an operating frequency of 235 kHz; a beamwidth of 6 degrees; and a 0 to 22 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat.

This in-hull or pocket mounted transducer uses narrow beams at low/high frequencies to display depth and temperature data to the Garmin Marine Network via a compatible sonar, such as the GSD 26. Note: In-hull  installation not recommended for cored-hull vessels.

Garmin 010-11868-21 Airmar SS60 600W 50/200 Thru-Hull Transducer With Garmin 8 Pin Connector 12° Tilt Version for 8-15° deadrise This stainless steel 600 W 8-pin transducer provides a vertical beam without a fairing and is excellent for fiberglass and wood hulls. It has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45/12 degrees; and 8 to 15 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging the boat.